1. Coleman Spas Hot Tub Error Codes 2017
2. Master Spa Hot Tub Error Codes
3. Coleman Spas Hot Tub Error Codes Chart

Have a consistent flo error code shown on your control panel, however, do now not know what must be accomplished to set itright; then you have stumbled upon the right place.

• If the spa is subsequently powered down and then powered up again, the HOt message will appear on the display and the spa will not be allowed to operate until a technician evaluates the spa and resets the HOt fault.
• Hot Tub Works remains committed to helping you keep your spa and hot tub safe, clean, and clear. While there may be shipping delays, we are processing and shipping orders as quickly as possible. Pool and Hot Tub Depot and the Pool and Hot Tub Depot Logo are registered trade-marks.
• When you get an “flo” message as a blunders code in your hot tub panel, expressed in numerous methods, “FL” “FLO” or ”FLOW.” It suggests that there’s no water flow or insufficient water flow through the hot tub heater which is caused due to a strain switch malfunctions or a flow switch malfunctions.

A lot of times you do not recognize whythe hot tub isn’t heating or the temperature is down in the preferred range these are a few things as a result of the flo error. Before we get into what causes an flo error and how to fix it, I must likely explain what a low flogenuinely is.

What is a hot tub flo error?

On either side of the hottub, there is a sensor that reads thewater pressure flowing through the system or a pressure switch located on yourheater element which does the same. These sensors check the flow of water andprevent it from going dry.

Balboa (used by LifeCast Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. Spa has shut down. One sensor has detected 118° F at heater. In addition to the Sn, Sn1, Sn2 type of error codes, other codes for Smart Sensor spas, such as SA, Sb, SnA, SnB error codes are used on many spas and hot tubs. These are similar to the Sn1 and Sn2 codes, signaled from the high limit or water temperature sensors. In summation; when you have spa trouble codes of Sn, SnA, Sn1, Sn2.

If theflow of water is not at the desired level, there are a lot ofchances of air running through it, and ifa heater or motor is running with air in it,then this is called as the system is running dry. If these are the problems in your hot tub, the sensor indicatesthe heater to shut down to protect itselffrom burning out and preventing any damage to the equipment.

What causes a hot tub flo error?

The indication of flo error usually means there may be a problemwith water flow in your hot tub.

When you get an “flo” message as a blunders code in your hot tubpanel, expressed in numerous methods, “FL” “FLO” or ”FLOW.” It suggests that there’s no water flow orinsufficient water flow through the hot tub heater which is caused due to a strain switch malfunctionsor a flow switch malfunctions.

There are a couple ofcommon causes for float mistakes in hot tubs; however The number one purpose ofa spa showing the error code “FLO” is because of a grimy or wiped outfilter system. Filters are usually the primary perpetrator as people don’t taketime to clean the cartridges quite often, so the pleats get clogged andrestrict the flow.

Water stage is also notan unusual aspect in flow errors, regardless of an insulating cover there islots of evaporation which take place and which could result in significant lossof water. If the water receives too low and the spa’s filter isn’t alwaysabsolutely submerged it is capable of drawing air into the gadget giving you a low go with the flow blunders.

Different types of water flo errors

Coleman Spas Hot Tub Error Codes 2017

The flo errorsare differentiated into many unique shows to slender down the FLO blunders.They are

1) Blinking FLO

The Heater has beendeactivated, the pump is on, andFlow or Pressure switch is open thismeans that the machine detects the spa has called for heat, which makes the PCboard apply strength to the pump. But the PC board has not detected water flowwhich makes the machine deactivate the heater to keep away from damage to theheater.

2) Solid FLO

The Pump is switched off, the flow or pressure switch is likewise closed which means the system hasnot detected flow because the PC Boardhas no longer applied pressure to the pump. However,the flow pressure switch is stating that there may be a water drift. The flowor pressure switch is stuck in the closed position or shorted.

These codes are a few of the most, not unique blunderscodes associated with drift problems or the pressure switch/flow switch. Theessential reason is the water flow through the spa control device, if the waterisn’t always flowing at a charge to satisfy the pressure switch, it will resultin one in every of the error codes indicated above.

How to trouble shoot water flo error?

Always remember that the filters should be rinsedthoroughly every month, and cleaned properly every three months or so and It has to be replaced annually orbi-annually if you use two different filters.

Video:

Conclusion

Master Spa Hot Tub Error Codes

Alwaysremember if your hot tub displayed an FLOmessage first test to see if there is any hair or debris wrapped across theFlow Switch paddle, then do the troubleshootingtechnique. If all else fails, then contact theService support team to book a diagnostic and repair your hot tub.

Coleman Spas Hot Tub Error Codes Chart

You’ll be capable of moreover flicking through this web site for morereviews regarding hot tubs and related things. Ifyou’ve got any queries, please feel free to comment, and we will resolveit to the best of our capability.